亚洲欧美一区二区久久|国产一区二区三区手机在线|日本欧美国产精品第一页久久|国产色产综合色产在线视频

Welcome to the official website of Dongguan Jinxin Shoes Machine Co., Ltd.! Favorite Feedback E-Map Chinese

Dongguan Jinxin Shoes Machine Co., Ltd.

Mainly engaged in the production of shoes, handbags, bags

Support Hotline:

15779636377

Your current postion:News >> FAQ >> 瀏覽文章

What should be paid attention to in the quality inspection of shoe factories?

Popularity:Issuing Time:2019-11-08 20:11:53

1. After climbing, the head shape is combined with the shape of the head, which helps the feet to be smooth and the back is curved.


2. According to the mark point, the height of the toe, the height of the mouth, the height of the back, and the error of the left and right feet should not exceed 1mm, otherwise it will be treated with double treatment;


3. The head shape is confirmed. The normal toe cap is similar to the edge of the shoe cover (possibly slightly inside the waist). If the thickness of both sides of the head is equal, the center is the standard, and the inward bias is 1mm. Outer waist


4. The injury is not acceptable;


5. There must be no wrinkles in Hong Kong and "chicken buttocks";


6. The squat line is acceptable to the inside as a whole 1.5mm, and should not be biased outside;


7. The shoe mouth and the line along the mouth are smooth, and cannot be high or low inside;


8. Leather pattern with double;


9. Hong Kong Treasures shall not be deformed after being affixed or smashed;


What should be paid attention to in the quality inspection of shoe factories?


10. The shoe production line company strictly follows the aircraft board operation;


11. The sneakers are attached to the back of the sneakers, the boots are smooth after the inserts, and the height of the boots is double;


12. The rupture of the shoes of the ruptured and plain shoes and the repair of the needle car line (slightly) are acceptable. When the injury is treated, the position can be repaired at the port of Hong Kong, and the repair of the port is not valid.


13. Epoxy: The leather is not allowed to overflow, and the width of the fabric and PU fabric is acceptable within 1mm.


14. Open glue: no tension on the sides of the inner and outer waists (no bends), the opening depth is 1mm, the length is about 1 inch, no need to fill the waist, but the outsole needs to be smooth;


15. Outsole of the outsole: acceptable for deviation from 0.5mm, the shoes are adjusted according to the heel of the heel of the heel at the heel of 1-2mm (as close as possible to the mid-sole);


16. The sanding exposure treatment is the same color as the leather material, but the surface should be smooth and clean, and there should be no rough surface;


17. Outsole wave


18. Pressure and pressure of the bottom press: Under the premise that the outsole is not deformed, the pressure and pressure are as large as possible;


19. The toe cap and other helpers are not open.




20. Do not have a clear injury (the heel is nailed, the upper is broken);


twenty one. Kick before and after: Can not kick before, kick 2mm after accepting, high heel, fine heel can not have front and back kick;


twenty two. The length of the toe cap, the height of the back, and the error of the left and right feet are 1.5mm;


twenty three. The hot bottom is smooth and has no wind;


twenty four. Big bottom branding, printing number confusion is unacceptable;


25. The color difference is acceptable within 2 degrees;


26. The post-treatment effect of the shoe production line company, compared with the sample, the gloss is even and natural;


27. Warpage: 5-6mm in tight shoes, 5-6mm in back, 3-4mm in front, 5-8mm in front and back;


28. In the latter part, it is necessary to pay special attention to the overall appearance of the finished shoes to be maintained in the shape of the hoe, which is not deformable seriously;


29. Packing specification inspection: single foot, wrong foot, wrong code, garbled, chaotic box, wrong type body box, etc.


Previous:沒有了Next:How to choose a suitable shoe machine?